CY7C68013A-56 chipset: Low-power version; Enhanced 51-core; 16KB program data areas; 48MHz frequency USB 2.0 compliant; up to 480Mbps transmission speed; Compatible with USB 1.1 EEPROM firmware: Complete in-system programming solution; Supports download with USB cable; On board 16K (24LC128) EEPROM for store VID / PID and USB firmware All GPIO are lead out through 2.4mm pin header Achieve logic analyzer functions with certain firmware A product for Arduino that works with official Arduino boards.
A product for Arduino that works with official Arduino boards.
Brand N/A Model 2560 R3 Quantity 1 Color Black + blue Material Immersion gold board Features Arduino Mega is a micro control development board based on ATmega2560 with 54 units I/O port (14 of them can be as PWM output) 16 units analog ratio input port and 4 units UART (hardware serial ports) and 16MHz crystal oscillator; Can download program through USB directly w/ bootloader; Power can be supplied by USB AC to DC adapter or battery; Can use Arduino language flash or processing quickly; Can download for free Specification Operating Voltage: 5V; Input Voltage (recommended): 7~12V; Input Voltage (limits): 6~20V; Digital I/O Pins: 54 (of which 14 provide PWM output; Analog Input Pins: 16; DC Current per I/O Pin: 40mA; DC Current for 3.3V Pin: 50mA; Flash Memory: 256KB of which 4 KB used by bootloader; SRAM: 8KB; EEPROM: 4KB; Clock Speed: 16MHz Application Used for learning / development Other Too low voltage will cause unstable while too high voltage will cause over-heat and damage Arduino MEGA; Thus suggested voltage is 6.5~12V recommended power voltage is 7.5V / 9V; A product for arduino that works with official Arduino boards English Manual/Spec http://arduino.cc/en/Main/Software Packing List 1 x Development board 1 x V3 expansion board 1 x Bread board 65 x Jumper wire (long: 24cm short: 10cm) 1 x USB cable (60cm)
Adopt 8-CH sampling sampling rate up to 24m/s; Support SPI IIC UART SMBus I2S CAN; Voltage range: 0~5V; USB interface plug and play simple to use Model USBEE AX MINI Quantity 1 Color Black Material Plastic + circuit board Features Max. Sampling rate: 24Msps; Sample rate: 24MHz @ 8 channels; Input voltage range: 0~5V; Digital channel: 8; Low input voltage: < 0.8V; High input voltage: >1.4V; Support protocol: SPI IIC UART SMBus I2S CAN Parallel Custom Search Async 1-Wite PS/2 Application Perfect for microcontroller's experiment Other Monitoring if program execution and programming are the same; Analyzes some protocol like I2C SPI TCP/IP etc. Packing List 1 x Logic analyzer 10 x DuPont lines (length: 18cm) 1 x USB cable (length: 71cm) Manual: http://m5.img.dxcdn.com/CDDriver/CD/sku.148945.rar
A product for Arduino that works with official Arduino boards. This improved board module is compatible with the original one convenient to use. Usage: - Download Arduino IDE: arduino.cc/en/Main/Software; - Download USB chip driver: wch.cn/downloads.php?name=pro&proid=65; Download link for foreign customers: wch-ic.com/download/list.asp?id=126; - Plug this development board then the driver will be installed automatically; - Choose MEGA2560 board from die; - Choose COM port - Best to choose and burn the Arduino built-in routine procedure first.
Features: 1. Completely solve the traditional UNO board is not compatible with Win7 and Win8 system instability 2. Increased pin socket to facilitate the use of DuPont line.
Micro USB Digispark Pro Development Board Kickstarter ATTiny167 For Arduino
Color Deep Blue Brand N/A Model R3 Quantity 1 Piece Material PCB + electronic components Chipset ATMEGA328 English Manual / Spec No Other Features A product for Arduino that works with official Arduino boards. Packing List 1 x Development board 1 x USB cable(50cm) 3 x 4-pin Terminals 1 x 6-pin Terminal 2 x 8-pin Terminals 1 x 10-pin Terminal
Introduction: 1. Supports Arduino IDE 1.0 + (OSX / Win / Linux) 2. Through USB or 5V or 7~35V (auto-match) extra power supply 3. There is a 500mA 5V regulator on the motherboard 4. USB embedding (serial debugging) 5. 6 I/O Pins (2 to support USB) 6. 8K Flash Memory (about 6k after bootloader) 7. I2C and SPI (vis USI) 8. PWM on 3 pins (more possible with Software PWM) 9. ADC on 4 pins 10. Power LED indicator and Test / Status LED (in Pin0)
Base shield is designed for the Arduino and its compatible interface development board. Make all the I/O pins on the Arduino leads into standard 4-pin interface form. Through which users can easily make Electronic module and Arduino link without considering the actual location of the corresponding pin. Considering the different Electronic module interface communication mode Base shield has digital analog I2C SPI compatible with different methods of communication interface. All by the side of the seat has clear instructions even a beginner don't worry connect wrong. Compatible with the Arduino and other development board has the same form. Compatible with all Electronic module more I2C interface convenient links. Clear indicator light work. Concise and complete plate printing information.
On board ZigBee wireless module port; On board CH340 chip suitable for serial communication test; CC Debugger interface of TI standard convenient to download and debug program also suitable for analyzer; With 5V to 3.3V AMS1117-3.3 chip; With LED power indicator and one programmable LED light; With reset button and two programmable buttons.
Brand N/A Model 2560 R3 Quantity 1 Color Black + blue Material Heavy gold plate Features Arduino Mega is a ATmega2560 as the core of microcontroller development board itself has 54 set of digital I/O input/output end (14 groups can do PWM output) 16 groups of simulated than the input four groups of UART (hardware serial ports) use the 16 MHz crystal oscillator. Specification Operating Voltage: 5V; Input Voltage (recommended): 7-12V; Input Voltage (limits): 6-20V; Digital I/O Pins: 54 (of which 14 provide PWM output); Analog Input Pins: 16; DC Current per I/O Pin: 40 mA; DC Current for 3.3V Pin: 50 mA; Flash Memory: 256 KB of which 8 KB used by bootloader; SRAM: 8 KB; EEPROM: 4 KB; Clock Speed: 16 MHz Application Learning board; development board Other Power supply design Arduino Mega power supply system there are two options the USB power supply directly or external power supply. The choice of power supply will automatically switch. The external power supply can choose AC - to - DC adapter or battery the limits of the control panel for the 6 v to 12 v voltage range but if the voltage is less than 6 v I/O mouth may not be able to provide to 5 v voltage so will appear unstable; If the voltage is greater than 12 v voltage stabilizer will likely overheating protection are more likely to damage the Arduino MEGA. Therefore suggested operating power supply of 6.5 ~ 12 V recommend the power is 7.5 V or 9 V. English Manual/Spec http://arduino.cc/en/Main/Software Packing List 1 x Development board 1x USB cable (60cm)